3D Design
Thursday, December 13, 2012
clay tiles
In order to create these tiles, I first had to make a plaster mold so that the shapes could be replicated. I chose the perfume bottle because I was drawn to the intricacies of the decorative flower and the potential for detail work in the cap. It was only when I started actually working on it did I actually realize how difficult it was going to be to not have undercuts, as the flower I was depicting had many of them. When I finished with the plaster mold, I came to the part where I actually had to start putting the clay in and allowing it to harden. Like many people in the class, I had trouble taking the tile out at the right time. Mine where either too hard and cracked, or too soft and tore away. I ended up with many unusable tiles and only three that were worth glazing. If I could go back, I would go the glaze jobs 100% differently, but I just didn't know how they would turn out since it was only my first try.
Tuesday, December 11, 2012
plaster carving abstracted from nature
At the beginning of this project, we were instructed to create an
organic shape out of clay, paying special attention to all the different
angles it could be seen from and different ways it could sit. I found
myself interested in the undulating tentacles of octopi so I started
playing with different ways to approach the subject. I decided, for the
sake of abstraction, that I should forgo including a head or any
recognizable features besides the actual tentacle forms.
Once the general shape had been chosen, we used a cardboard box to pour wet plaster in to make a mold. When the plaster was dry, we tore the cardboard away are were left with a rectangular chunk of plaster. The task figuring out where the tentacles should be in a hulking plaster block was both daunting and perplexing. I tried to draw the outlines on the sides of the block but got even more confused. Finally, I discovered that the easiest way to approach it (at least for my project) was to figure out the heights of the tentacles so I knew for sure where I could start cutting away.
As the piece started progressing, I learned which tools were better for what and became more confident in my skills. I began thinking in terms of positive and negative space, and how best to balance the two. Since the plaster block was more vertical than my original clay mold, I had to compensate by carving up rather than out. And the further I got, the more I realized that the carving had a mind of it's own. Though I wanted to include eight tentacles, the space and flow of the piece did not allow for it, so I just did what I felt was most aesthetically pleasing. If anyone actually takes the time to count tentacles, I will just follow up with, "it's an abstraction" and be done with it.
This is the final, sanded down product of my work. Though it's quite a bit different from my original clay design, I am happy with the way it turned out. I feel it captures the subtle grace of an octopus' tentacles while not being too obvious. After the critique, I did a little work on the bottom so it wasn't just a flat plane. Though I would have carved more deeply and perhaps hollowed out the center if I'd had the time, I am at least content with the fact that it sits much better on a desk surface now.
FINISHED VIEW 1
FINISHED VIEW 2
FINISHED VIEW 3
Once the general shape had been chosen, we used a cardboard box to pour wet plaster in to make a mold. When the plaster was dry, we tore the cardboard away are were left with a rectangular chunk of plaster. The task figuring out where the tentacles should be in a hulking plaster block was both daunting and perplexing. I tried to draw the outlines on the sides of the block but got even more confused. Finally, I discovered that the easiest way to approach it (at least for my project) was to figure out the heights of the tentacles so I knew for sure where I could start cutting away.
As the piece started progressing, I learned which tools were better for what and became more confident in my skills. I began thinking in terms of positive and negative space, and how best to balance the two. Since the plaster block was more vertical than my original clay mold, I had to compensate by carving up rather than out. And the further I got, the more I realized that the carving had a mind of it's own. Though I wanted to include eight tentacles, the space and flow of the piece did not allow for it, so I just did what I felt was most aesthetically pleasing. If anyone actually takes the time to count tentacles, I will just follow up with, "it's an abstraction" and be done with it.
This is the final, sanded down product of my work. Though it's quite a bit different from my original clay design, I am happy with the way it turned out. I feel it captures the subtle grace of an octopus' tentacles while not being too obvious. After the critique, I did a little work on the bottom so it wasn't just a flat plane. Though I would have carved more deeply and perhaps hollowed out the center if I'd had the time, I am at least content with the fact that it sits much better on a desk surface now.
FINISHED VIEW 1
FINISHED VIEW 2
FINISHED VIEW 3
Tuesday, September 18, 2012
For the wire sculpture project, I ended up choosing to make a compact mirror brush, minus the mirror. I started out by choosing a thick gauge wire and creating the cylindrical shape. The thick wire helped with the stability of the piece, though it was quite difficult to bend.
I then added some cross hatching wires to connect the bristles of the brush to. This started to become difficult due to the bowing of the previously constructed circular wire formation. The circle ended up somewhat warped, but I did my best to correct it. I also added thinner wire arched over the center circular structure to form the rounded dome-like surface from which the bristles would protrude.
Finally, I added the brush bristles. I chose to leave a loop at the tops of them to represent their circular tips, and entwined the bases to the cross hatch structure. I chose a medium gauge wire for these so they were strong enough to stand rigidly, but pliable enough the bend around the wire at the base, to form a stable foundation.
I then added some cross hatching wires to connect the bristles of the brush to. This started to become difficult due to the bowing of the previously constructed circular wire formation. The circle ended up somewhat warped, but I did my best to correct it. I also added thinner wire arched over the center circular structure to form the rounded dome-like surface from which the bristles would protrude.
Finally, I added the brush bristles. I chose to leave a loop at the tops of them to represent their circular tips, and entwined the bases to the cross hatch structure. I chose a medium gauge wire for these so they were strong enough to stand rigidly, but pliable enough the bend around the wire at the base, to form a stable foundation.
Tuesday, August 28, 2012
This video, entitled Day Breaking, includes stills from an hours worth of video documenting the sunrise. After a series of failed attempts at other ideas, the sunrise seemed to be the most viable option in the time I had remaining to complete the assignment. As I'm on the 11th floor of my residence hall, this is the sight I wake up to every morning. But for the purposes of this project, I got up a bit earlier and met the sun when it rose.
Subscribe to:
Posts (Atom)